Why Armature Winding on Stator in Synchronous Machine?


In Synchronous Machine, the armature winding is provided on Stator and field winding on Rotor which is contrary to other Electrical Machines. In fact there are certain issues due to which we provide armature winding on Stator. The benefits of this are as follows:

More Economical:

It is more economical to provide Armature winding on Stator and Field winding on rotor. Let us consider a three phase Star connected 750 MVA, 21 kV Synchronous Machine.


Line Current = (750x103)/(1.732x21) = 20,620 A

If the armature winding is placed on the Rotor, we need three slip rings each capable of handling 20,620 A. Only not this, we need to provide slip rings with an insulation of (21/1.732 = 12.12 kV). The star point for grounding is also to be taken out through the fourth slip ring.

Now, suppose the power requirement for the Field is 2 MW at 500 V. Then

Excitation / Field Current = 2000/0.5 = 4000A

In this case only two Slip Rings each capable of handling 4000 A is required. Also, the insulation requirement for slip ring in this case is only 500 V.

This means it is far better and cheaper to use Field winding on the Rotor instead of armature.


More Efficient:

With armature on the Stator and Field winding on the Rotor, only two slip rings are required due to which losses associated with slip ring and carbon brushes are reduced and efficiency increases.

Better Insulation:

As armature winding is stationary, therefore it is possible to insulate the armature winding for higher voltage level and making it possible to generate power at higher voltage up to 33 kV.

Better Cooling:

Better cooling of Armature winding is possible as the winding is stationary. This is the reason that DM (Demineralized Water) cooling is done for armature winding.

More Power Output:

As the cooling is efficient because of stationary armature winding and rotor weight is also less, therefore higher rotor speed is possible, thus increasing the Synchronous Machine output for a given dimension.

More Armature Tooth Strength:


High current Synchronous Machine require more armature copper for each slot. Greater amount of Copper can be accommodated if the Slot / Tooth is deeper and strong enough. If the Armature would have been on Rotor then Slot / Tooth would have been narrow and weaker. Thus armature on the Stator allows stronger and deeper Slot / Tooth. Strong Teeth also reduces the noise due to vibration and are less likely to be damaged during fabrication and use.


Comments

Post a Comment

Popular posts from this blog

Concept of Subtransient, Transient & Steady State

Image
The concept of Subtransient, Transient and Steady State arises in case of fault in an Alternator. Let us assume a sudden short circuit in three phase of alternator. The fault current will flow in all the three phases of alternator and its waveform will be as shown in figure below. When the alternator is short-circuited, the currents in all the three-phases rise rapidly to a high value of about 10 to 18 times of full load current, during the first quarter cycle. The flux crossing the air gap is large during a first couple of cycles. The reactance during these first two or three cycle is least and the short circuit current is high. This reactance is called subtransient reactance and is denoted by X". The first few cycles come under sub-transient state. After a first few cycles, the decrement in the r.m.s. value of short circuit current is less rapid than the decrements during the first few cycles. This state is called the Transient  State and the reactance in th
Read more

Open Circuit and Short Circuit Characteristics of Synchronous Machine

Image
Open Circuit Test and Short Circuit Test are performed on a Synchronous Machine to find out the parameters of Synchronous Machine and hence to have an idea of their performance.  Open Circuit Test of Synchronous Machine is also called No Load, Saturation or Magnetizing Characteristics for the reason which will be clear after going through the post. For getting the Open Circuit Characteristics of Synchronous Machine, the alternator is first driven at its rated speed and the open terminal voltage i.e. voltage across the armature terminal is noted by varying the field current. Thus Open Circuit Characteristic or OCC is basically the plot between the armature terminal voltage E f versus field current I f while keeping the speed of rotor at rated value. It shall be noted that for OCC, the final value of E f shall be 125% of the rated voltage. Figure below shows the connection diagram for performing the Open Circuit Test of Alternator. As clear from the figure above
Read more

Restricted Earth Fault Protection of Transformer

Image
Restricted Earth Fault (REF) protection is basically a Differential Protection. The only difference in between the Differential Protection and REF Protection is that, latter protection is more sensitive as compared to the former protection scheme. In earlier posts we have already discussed Differential Protection of Transformer and various characteristics of Differential Protection. In this post we will focus on Restricted earth Fault protection. Also Read, Transformer Differential Protection Percentage Differential Protection - Slope in Differential Protection Harmonic Restraining in Differential Protection For the sake of understanding REF Protection, we take a Transformer of configuration DYn i.e. HV side of Transformer is Delta connected while the LV side is Start connected and neutral is grounded solidly. As shown in figure above, there are a total of four Current Transformers (CTs), three CTs connected in each phase i.e. R, Y and B and one CT connected in neutral. The secondary o
Read more