Rating of Synchronous Generator or Alternator


The rating of AC Machines such as Transformer, Alternators etc. are determined by the heating and hence losses in them. These losses are made up of Ohmic (I2R loss ) and Core Loss and a small amount of friction & windage loss. The ohmic loss depends upon the current and the core loss depends upon the voltage, therefore the losses in an electrical AC machine are unaffected by the power factor of the load. In view of this, the rating of AC machinery is determined by volt-ampere of the load not by the load power alone. Therefore the Alternators or Synchronous Generators are rated in kVA or MVA.

You may like to read Losses in Electrical Machine - Core Loss and Eddy Current Loss

It shall be noted here that the size of boiler or the fuel requirement is solely determined by the output power and not on the volt-ampere. For example, for 700 MW load at 0.85 power factor, the rating of Alternator or Synchronous Generator will be 823 MVA (700/0.85 = 823) while the fuel requirement and size of boiler will be decided by 700 MW. To be more accurate, as the efficiency of Carnot Cycle is around 33%, if we assume Carnot Steam Cycle for simplicity then the fuel requirement or size of boiler to generate a power of 700 MW will be around 3 times the output power i.e. 3x700 = 2100 MW. It is very surprising that only 1/3 of the total input power (2100 MW) is converted into electrical power output but it’s true. Remaining power is lost in NDCT (Natural Draft Cooling Tower and losses during the whole steam cycle).


It shall be mind here that for stating the rating of an Alternator, we must include the steady state operating power factor along with the MVA / kVA rating. The need for mentioning power factor arises because the Alternator designed to operate at 0.85 power factor will require more filed current if operated at 0.8 power factor to maintain constant terminal voltage. More filed current at lower power factor means more losses in the field winding which in not desirable. If on the name plate of an Alternator, it is not mentioned that whether the power factor is lagging or leading then it shall be assumed to be lagging because for constant terminal voltage, lagging power factor will require more field current than the leading power factor. Thus lagging power factor puts a limit on exciter output and current in the field coil.

Under rated power and voltage conditions, reactive power flow handled by an Alternator is limited by the armature heating for operating power factor near the rated value. If the operating power factor is away from the rated value, then the reactive power flow is limited by both the armature and filed heating. Figure below shows a typical Name Plate of a Generator of 120 MW. Mind the kVA rating and Power factor.

You may like to read Why Hydrogen used for the Rotor Cooling of Generator
  

Normally Generator Capability Curve is provided by the manufacture from which we can get the operating point and the various limits like armature heating, filed heating and End part heating. We will be discussing the Generator Capability Curve in next post.

Comments

Post a Comment

Popular posts from this blog

Concept of Subtransient, Transient & Steady State

Image
The concept of Subtransient, Transient and Steady State arises in case of fault in an Alternator. Let us assume a sudden short circuit in three phase of alternator. The fault current will flow in all the three phases of alternator and its waveform will be as shown in figure below. When the alternator is short-circuited, the currents in all the three-phases rise rapidly to a high value of about 10 to 18 times of full load current, during the first quarter cycle. The flux crossing the air gap is large during a first couple of cycles. The reactance during these first two or three cycle is least and the short circuit current is high. This reactance is called subtransient reactance and is denoted by X". The first few cycles come under sub-transient state. After a first few cycles, the decrement in the r.m.s. value of short circuit current is less rapid than the decrements during the first few cycles. This state is called the Transient  State and the reactance in th...
Read more

Open Circuit and Short Circuit Characteristics of Synchronous Machine

Image
Open Circuit Test and Short Circuit Test are performed on a Synchronous Machine to find out the parameters of Synchronous Machine and hence to have an idea of their performance.  Open Circuit Test of Synchronous Machine is also called No Load, Saturation or Magnetizing Characteristics for the reason which will be clear after going through the post. For getting the Open Circuit Characteristics of Synchronous Machine, the alternator is first driven at its rated speed and the open terminal voltage i.e. voltage across the armature terminal is noted by varying the field current. Thus Open Circuit Characteristic or OCC is basically the plot between the armature terminal voltage E f versus field current I f while keeping the speed of rotor at rated value. It shall be noted that for OCC, the final value of E f shall be 125% of the rated voltage. Figure below shows the connection diagram for performing the Open Circuit Test of Alternator. As clear from the figure a...
Read more

Transformer Cooling Classes

Image
Losses in the transformer are of the order of 1% of its full load kW rating. There are mainly two types of losses in a Transformer i.e. Core Loss and Ohmic Loss. Because of these losses the winding of transformer as well as Core gets heat up and we need to provide sufficient cooling to remove heat and maintain a constant winding and Core temperature. Various types of cooling methodologies are used for Transformer but before going to each methodology, we will have a look at the General Method of designating a particular cooling method i.e. class. In the nameplate of Transformer, four letter represents the cooling method of the Transformer. The above table is self explanatory, therefore if you see ONAN on the Name Plate of Transformer then it means that Oil with flash point less than 300° is used as cooling media and Natural convection is used for removing heat. In secondary side of cooling mechanism, Air with Natural convection is used by employing Radiator. ...
Read more